|
|
|
 |
您當前所在的位置：返回首頁 >> 產品中心 |
|
| 雙股刺繩機CS-A |
| 【更新時間：2015-06-16】 【點擊次數：25次】 【字體：大 中 小】 【打印】 【關閉】 |
1、刺網機說明
一、用途、性能
該機主要適用于生產各種多股刺鋼絲，其使用材料應符合GB/T343-94標準要求《一般用途熱鍍鋅低碳鋼絲》，該產品廣泛使用于國防、鐵路、調整公路、農畜牧等行業。
CS-A型刺鋼絲機由繞絲和收絲加捻二部分連接組成（見圖書1、圖2），并配套四只放絲盤，該機各部件工作協調，動作平穩，操作靈活可靠，是生產刺鋼繩的專用設備。
二、主要技術參數
1、CS-A型刺鋼絲機的主要技術參數見表2 |
| 序號 |
項目 |
單位 |
基本參數 |
| 1 |
電動機 |
KW |
2.2 |
| 2 |
主傳動軸轉速 |
r/min |
432 |
| 3 |
理論產量 |
Kg/h |
90 |
| 4 |
整機重量 |
kg |
1200 |
| 5 |
主機部分 |
mm |
1900×1300×980 |
| 6 |
收繩加捻部分 |
mm |
1800×750×750 |
注：特殊需要按供需雙方約定。
2、刺鋼繩的規格范圍見表2 |
| 序號 |
項目 |
單位 |
基本參數 |
| 1 |
刺距 |
mm |
76(3寸）102（4寸） |
| 2 |
捻數 |
個 |
4 |
| 3 |
股絲直徑 |
mm |
2.2-2.8 |
| 4 |
刺絲直徑 |
mm |
1.8-2.2 |
1, gill nets machine instructions
1, uses, performance
Machine is mainly applicable to the production of a variety of multi-strand barbed wire, the use of materials should meet the standard requirements GB/T343-94 "general purpose hot-dipped galvanized low carbon steel wire," the products are widely used in national defense, railway, adjust the highway, agricultural livestockand other industries.
CS-A-type barbed wire around the wire machine and the income from the two parts connected to form a filament twist (see Book 1, Figure 2), and matching silk put four plates, coordinating the work of the various components of the aircraft movements, stable, flexible operation and reliable,is the currently the only product barbed rope equipment.
2, the main technical parameters
1, CS-A-type barbed wire machine Main technical parameters of Table 2 |
| No. |
Item |
Units |
Basic parameters |
| 1 |
Motor |
KW |
2.2 |
| 2 |
Main Drive Shaft Speed |
r/min |
432 |
| 3 |
Theoretical yield |
Kg/h |
90 |
| 4 |
Total Weight |
kg |
1200 |
| 5 |
The host part of the |
mm |
1900×1300×980 |
| 6 |
Size of the pull-twist part of the |
mm |
1800×750×750 |
Note: special needs agreement by both supply and demand.。
2, barbed wire line the scope of the specifications in Table 2 |
| No. |
Item |
Units |
Basic parameter |
| 1 |
distance |
mm |
76(3Inch）102（4Inch） |
| 2 |
Twist number |
piece |
4 |
| 3 |
Unit wire diameter |
mm |
2.2-2.8 |
| 4 |
Barbed wire diameter |
mm |
1.8-2.2 |
|
|
|
